Proface LT3300 - 5.7 All-in-One HMI" Manuel d'utilisateur

/76HULHV+DUGZDUH0DQXDO

9Package ContentsThe following items are included in the LT unit’s package. Before using the LT, please check that all items listed here are present.T

10Installation prerequisites for standards• UL listed products• c-UL listed products• Product ListUL/c-UL File No.E220851, E210412For the detailed cer

11<Cautions> Be aware of the following items when building the LT into an end-use product:• The LT unit’s rear face is not approved as an enclos

12CE MarkingThe following units are CE marked products complying with the EMC Directive.For the detailed information on CE Marked, be downloaded and r

13ContentsPreface... 1Essential Saf

142.2.2 Performance Specifications ...2-192.2.3 Interface Specifications

1-11 Overview1. System Design2. Accessories3. Part Names and FunctionsThis chapter describes peripheral devices that can be connected to LT Series uni

LT3000 Series Hardware Manual1-21.1 System Design1.1.1 LT-3200 SeriesThe following diagram illustrates the standard range of items that can be connect

Chapter 1 Overview1-3 Edit Mode Peripherals*1 For supported models, refer to Pro-face’s support site “Otasuke Pro!” (http://www.pro-face.com/otasuke/

LT3000 Series Hardware Manual1-41.1.2 LT-3300 SeriesThe following diagram illustrates the standard range of items that can be connected to LT-3300 Ser

1PrefaceThank you for purchasing Pro-face’s LT3000 Series Graphic Logic Controller Interface (Hereafter referred to as the “LT unit”).Before operating

Chapter 1 Overview1-5*1 For supported models, refer to Pro-face’s support site “Otasuke Pro!” (http://www.pro-face.com/otasuke/). You can connect to t

LT3000 Series Hardware Manual1-61.2 AccessoriesAll accessories listed here are produced by Digital Electronics Corporation.1.2.1 USB Host Interface1.2

Chapter 1 Overview1-71.2.3 Option Items1.2.4 Maintenance ItemsProduct Name Model No. Corresponding LT DescriptionScreen Protection SheetCA6-DFS4-01 LT

LT3000 Series Hardware Manual1-81.2.5 EX Module(Expanded I/O Unit for LT3000 Series use)Up to two EX modules can be connected to the rear side of the

Chapter 1 Overview1-9Analog Input ModuleAnalog Output ModuleAnalog I/O ModuleProduct Name Model No. DescriptionEX module (2-ch analogue-input modul

LT3000 Series Hardware Manual1-101.3 Part Names and Functions1.3.1 LT-3200 SeriesA: Status LEDThis LED indicates the LT’s status, e.g. power input, fi

Chapter 1 Overview1-111.3.2 LT-3300 SeriesA: Status LEDThis LED indicates the LT’s status, e.g. power input, firmware RUN status or backlight conditio

LT3000 Series Hardware Manual1-12

2-12 Specifications1. LT-3200 Series2. LT-3300 SeriesThis chapter describes the general, functional and interface specifications of the LT as well as

LT3000 Series Hardware Manual2-22.1 LT-3200 Series2.1.1 General Specifications Electrical Specifications Environmental SpecificationsPower SupplyInp

2Essential Safety PrecautionsAll safety-related procedures stated in this document must be followed to operate the LT correctly and safely. Be sure to

Chapter 2 Specifications2-3 Structural SpecificationsInstallationGroundingGrounding resistance of 100Ω 2mm2 or thicker wire, or your country’s applic

LT3000 Series Hardware Manual2-42.1.2 Performance Specifications Performance SpecificationsApplication*1*1 It is user active capacity.FLASH EPROM 6MB

Chapter 2 Specifications2-5 Display Specifications Touch Panel SpecificationsDisplay Type Monochrome Amber/ Red LCDResolution W320 x H240 pixelsDot

LT3000 Series Hardware Manual2-62.1.3 Interface SpecificationsThis section describes the specifications of each interface of the LT Series unit. DIO

Chapter 2 Specifications2-7 Input DeratingUsing LT input voltage that exceeds the rated voltage, the input ON voltage, the number of input points or

LT3000 Series Hardware Manual2-8• Input Circuit Output SpecificationsOutput Terminal OUT0 to OUT3 OUT4 to OUT5Rated Voltage DC24VAllowable Voltage Ra

Chapter 2 Specifications2-9• LT3201-A1-D24-K Output Circuit (Sink type)• LT3201-A1-D24-C Output Circuit (Source type)• Since the output terminals are

LT3000 Series Hardware Manual2-10 High-Speed Counter / Pulse Catch Input SpecificationsDIO Standard Input/Output is used as a High-Speed Counter Inpu

Chapter 2 Specifications2-11 Pulse/PWM Output SpecificationsDIO Standard Input/Output is used as a Pulse Output or PWM Output. The setup is done by t

LT3000 Series Hardware Manual2-122.1.4 Wiring to the DIO Connector Items Required to Wire Connectors• ScrewdriverRecommended type: 1891348-1 <Tyco

3Design a circuit that will supply power to the LT unit’s I/O before starting up the LT. If the LT unit’s internal program enters RUN mode prior to th

Chapter 2 Specifications2-133. The adjacent wire insertion hole (round-shaped hole) will be in an open state.With the flathead screwdriver still inser

LT3000 Series Hardware Manual2-142.1.5 DimensionsThe following dimensions apply to LT-3201A unit. Installation Fasteners Attached DimensionsUnit: mm[

Chapter 2 Specifications2-15  Cable Attached DimensionsUnit: mm[in.]• All the above values are designed in case of cable bending. The dimensions give

LT3000 Series Hardware Manual2-16 Panel Cut DimensionsUnit: mm[in.] Installation FastenersUnit: mm[in.]118.5+0.04-092.5+1-04-R3[0.12] or lessPanel t

Chapter 2 Specifications2-172.2 LT-3300 Series2.2.1 General Specifications Electrical Specifications Environmental SpecificationsPower SupplyInput V

LT3000 Series Hardware Manual2-18 Structural SpecificationsInstallationGroundingGrounding resistance of 100Ω 2mm2 or thicker wire, or your country’s

Chapter 2 Specifications2-192.2.2 Performance Specifications Performance SpecificationsModel LT-3300L/LT-3300S/LT-3300T LT-3301LApplication*1*1 It is

LT3000 Series Hardware Manual2-20 Display Specifications Touch Panel SpecificationsModelLT-3300LLT-3301LLT-3300S LT-3300TDisplay Type Monochrome LCD

Chapter 2 Specifications2-212.2.3 Interface SpecificationsThis section describes the specifications of each interface of the LT Series unit.• The LT u

LT3000 Series Hardware Manual2-22Serial Interfaces (COM1)This interface is used to connect an RS232C/RS422/RS485 *1 cable. D-sub 9-pin plug connector

4HandlingWiringMaintenanceWiring Layout PrecautionsInstallationDo not disassemble or modify the LT unit. Doing so may cause a fire or an electric shoc

Chapter 2 Specifications2-23 DIO Interface (Connector) Input Specifications• When preparing the cable to connect the wiring, check the pin numbers i

LT3000 Series Hardware Manual2-24 Input DeratingUsing LT input voltage that exceeds the rated voltage, the input ON voltage, the number of input poin

Chapter 2 Specifications2-25• Input Circuit Output SpecificationsOutput Terminal OUT0 to OUT3 OUT4 to OUT15Rated Voltage DC24VAllowable Voltage Range

LT3000 Series Hardware Manual2-26• LT330*-*1-D24-K Output Circuit (Sink type)• Since the output terminals are not electrically protected, an output li

Chapter 2 Specifications2-27• LT330*-*1-D24-C Output Circuit (Source type)• Since the output terminals are not electrically protected, an output line

LT3000 Series Hardware Manual2-28 High-Speed Counter / Pulse Catch Input SpecificationsDIO Standard Input/Output is used as a High-Speed Counter Inpu

Chapter 2 Specifications2-29 Pulse/PWM Output SpecificationsDIO Standard Input/Output is used as a Pulse Output or PWM Output. The setup is done by t

LT3000 Series Hardware Manual2-302.2.4 Wiring to the DIO Connector Items Required to Wire Connectors• ScrewdriverRecommended type: 1891348-1 <Tyco

Chapter 2 Specifications2-313. The adjacent wire insertion hole (round-shaped hole) will be in an open state.With the flathead screwdriver still inser

LT3000 Series Hardware Manual2-322.2.5 DimensionsThe following dimensions apply to LT-3300 series unit.The dimensions of the LT-3301* are the same. Th

5WiringMaintenanceUnit DisposalGeneral Safety PrecautionsBe sure to ground the LT unit’s FG wire separately from other equipment FG lines. Also, be su

Chapter 2 Specifications2-33Cable Attached DimensionsUnit: mm[in.]• All the above values are designed in case of cable bending. The dimensions given

LT3000 Series Hardware Manual2-34 Panel Cut DimensionsUnit: mm[in.] Installation FastenersUnit: mm[in.]156.0+0.04-0123.5+1-04-R3[0.12] or lessPanel

3-13 Sample of the Circuit Diagrams1. Examples of Particular I/O Connections

LT3000 Series Hardware Manual3-23.1 Examples of Particular I/O Connections3.1.1 Connection to Pulse Motor Amplifier (CW/CCW type)The following circuit

Chapter 3 Sample of the Circuit Diagrams3-3 Output Source Type• The output terminals for LT pulses are the ones that have the signal names OUT0, OUT

LT3000 Series Hardware Manual3-43.1.2 Connection to Pulse Motor Amplifier (Clock Up/Down System)The following circuit diagrams show examples of connec

Chapter 3 Sample of the Circuit Diagrams3-5 Output Source Type• The output terminals for LT pulses are the ones that have the signal names OUT0, OUT

LT3000 Series Hardware Manual3-63.1.3 Connection to a Rotary EncoderThe following circuit diagrams show examples of connections between the LT and a r

4-14 Installation and Wiring1. Installation2. Wiring Precautions3. USB Cable Clamp Attachment/Removal

LT3000 Series Hardware Manual4-24.1 InstallationThis section describes the procedures and precautions for installing the LT Series units. Check the I

6LCD Panel Usage Precautions• The LCD panel’s liquid contains an irritant. If the panel is damaged and any of this liquid contacts your skin, immedi-a

Chapter 4 Installation and Wiring4-3 Installation Requirements• For easier maintenance, operation, and improved ventilation, be sure to install the L

LT3000 Series Hardware Manual4-4• When installing the LT in a slanted panel, the panel face should not incline more than 30°.• When installing the LT

Chapter 4 Installation and Wiring4-5 Installing the LT(1) Insert the LT into the panel cut, as shown.(2) Insert the installation fasteners into the L

LT3000 Series Hardware Manual4-6(3) Insert each of the fasteners shown below. Be sure to pull the fastener back until it is flush with the rear of the

Chapter 4 Installation and Wiring4-74.2 Wiring PrecautionsThis section describes the procedures and precautions for wiring power cords.4.2.1 Connectin

LT3000 Series Hardware Manual4-8 When the DC TypePower Cord SpecificationsPower Connector (Plug) SpecificationsWiringWhen connecting the Power Cord,

Chapter 4 Installation and Wiring4-9Connecting the Power Cord(1) Confirm that the power cord is unplugged from the power supply.(2) Strip the membrane

LT3000 Series Hardware Manual4-104.2.2 Connecting the Power SupplyThis section describes the precautions for supplying a power voltage.• If the suppli

Chapter 4 Installation and Wiring4-114.2.3 GroundingThis section describes the precautions for grounding the LT unit.• When supplying power to the LT

LT3000 Series Hardware Manual4-124.2.4 Wiring PrecautionsTo help prevent noise and interference problems, separate all control, communication and powe

7Information SymbolsThis manual uses the following icons:About the ManualsFor the detailed information on LT3000 Series, refer to the following manual

Chapter 4 Installation and Wiring4-134.2.5 Installation PrecautionsExternal power failure or failure of the LT unit may cause abnormal behavior.To pre

LT3000 Series Hardware Manual4-14 Emergency Stop CircuitDo not process emergency stop signals with a software program by inputting the signal to the

Chapter 4 Installation and Wiring4-15 Interlock Circuit 2If there is a possibility that the abnormal operation of the LT may lead to an accident, des

LT3000 Series Hardware Manual4-164.3 USB Cable Clamp Attachment/RemovalThis clamp is used to prevent the USB cable connected to the USB Host Interface

Chapter 4 Installation and Wiring4-17(3) Insert the USB cable into the USB Host Interface.(4) Attach the USB cover to the USB host interface. Insert t

LT3000 Series Hardware Manual4-18(2) With the main unit display part positioned so that it is facing down, attach the USB holder to the USB host inter

Chapter 4 Installation and Wiring4-19 Removal(1) Pull out the USB cover from the USB holder by pressing down the tab on the USB cover.(2) Insert the

LT3000 Series Hardware Manual4-20

5-15 Maintenance1. Cleaning the Display2. Periodic Check Points3. Replacing the Installation Gasket4. Replacing the BacklightThis chapter explains cau

LT3000 Series Hardware Manual5-25.1 Cleaning the DisplayWhen the surface or frame of the display become dirty, soak a soft cloth in water with a neutr

8LT3000 Series Model Name IndicationModel nameLT 3 * ** - * 1 - *** - *LT3000 Series Model NamesThe term “LT3000” Series refers to the following LT mo

Chapter 5 Maintenance5-35.2 Periodic Check PointsTo keep your LT unit in its best condition, please inspect the following points periodically. LT Op

LT3000 Series Hardware Manual5-45.3 Replacing the Installation GasketThe installation gasket provides protection against dust and moisture. Installat

Chapter 5 Maintenance5-5• The gasket must be inserted correctly into the groove for the LT’s moisture resistance to be equivalent to IP65f.• Since th

LT3000 Series Hardware Manual5-65.4 Replacing the Backlight• The LT’s backlight cannot be replaced by the user. When the backlight needs to be replace